Microphone Test
See whether your mic picks up sound with a live level meter and waveform, and record 5 or 10 seconds to hear yourself. Nothing is saved.
Loading the tool…
Used this tool? Share what worked for you — it helps the next person.
Microphone Test: complete guide
Walk through the steps and examples, or jump straight to the topic you need.
At a glance
- Measurement
- Shows the average (RMS) and maximum (peak) of the input sound in dBFS. On the bar, -60 dB is the left end and 0 dB is the right end.
- Verdicts
- A peak of -1 dB or higher, or touching the maximum, is distorted; -6 dB or higher is a bit loud; -30 dB or higher is just right; anything above -60 dB is quiet.
- Settings
- If you change the input device, echo cancellation, noise suppression, or auto gain control, it reconnects under the new conditions and shows the values actually applied.
- Recording
- Record 5 or 10 seconds and listen right away. The recording isn't saved and disappears when you close the page.
- Requirements
- A secure connection (HTTPS) and microphone permission are needed.
How to use Microphone Test
Turn on the microphone
Press "Turn mic on" and click Allow in the browser window. A notice is shown while permission is being checked.
Speak and watch the bar
Speak or clap and see whether the "Input level" bar and the average and maximum values move. In "View" you can switch between the waveform and the frequency display.
Change settings and compare
Choose the microphone you actually use under "Input device", and turn echo cancellation, noise suppression, and auto gain control on and off to see the difference.
Record and listen
Choose "Recording length" of 5 or 10 seconds and record, and you can play it back right after it ends.
What it’s good for
How to read the volume bar
The left end of the bar is -60 dB and the right end is 0 dB (maximum). While you speak, a peak between -30 and -6 dB is about right; if it touches 0 dB the sound distorts, so lower the input volume. If the bar stays high even when you're silent, background noise or electrical noise is getting in.
Should I turn on echo cancellation and noise suppression?
For video calls, it's better to leave them on. When recording an instrument or singing, noise suppression can erase even quiet sounds and lower the quality, so turn it off and compare. When you change a setting, it reconnects under the new conditions and also shows the values the browser actually applied.
When you can't hear any sound
Check that you've allowed microphone permission in the site settings left of the address bar, and that the browser's microphone access is turned on in the Windows or macOS privacy settings. Choose the microphone you actually use as the input device, and also check whether a headset mute switch or a video-call app is holding the microphone.
Worked examples
A sound at a good level
A sound at a level of 0.1 (10% of the maximum)Average −20.0 dB · Peak −20.0 dB
The level is just right · bar 66.7%A sound that is too quiet
A sound at a level of 0.005Peak −46.0 dB · The sound is quiet
Bar 23.3%A sound that hits the maximum
A sound that reaches the maximum (±1)Peak 0.0 dB
The sound is clipping (hit the maximum)Choosing microphone settings
Swipe the table sideways to see the rest.
| Setting | When on | What to check |
|---|---|---|
| Echo cancellation | Reduces the echo of speaker sound getting back in. | With earphones, you can often turn it off. |
| Noise suppression | Reduces background noise such as fans and keyboards. | It can erase even a quiet voice, so turn it off and compare. |
| Auto gain control | Raises quiet sounds and lowers loud ones. | Try it when the recording is too quiet. |
When the result isn’t what you expected
It says microphone access was denied
Allow the microphone in the site settings next to the address bar, then refresh. Once you block it, the browser doesn't ask again.
It says another app is using the microphone
This is when a video-call or recording app is holding the microphone. Close that app and turn it on again.
It says no microphone was found
Either no microphone is connected or the operating system is blocking it. On Windows, turn on your browser in Settings › Privacy › Microphone; on macOS, in Privacy & Security › Microphone.
It says it only works over a secure connection
The microphone can only be used on a page whose address starts with https. Check the address and open it again.
Key terms
- dBFS
- A unit of sound level that puts the digital maximum at 0. The closer to 0, the louder, and values are usually negative.
- RMS (average)
- The average sound level over a period of time. It is close to the loudness you perceive by ear.
- Clipping
- The effect where sound exceeds the maximum, gets cut off, and distorts.
Microphone Test FAQ
Does the recorded sound go to a server?
No. The recording is only played back inside this browser and is never saved or sent. It disappears when you close the page. To keep it as a file, use a voice recorder.
Does it work on a phone?
Yes. If you allow microphone permission in Chrome on Android or Safari on iPhone, you can check it the same way.
The dB value is negative. Is that normal?
Yes. It is a unit that puts the maximum at 0 dB, so real sounds come out negative. While you speak, a peak between −30 and −6 dB is just right.
Can I make the recording longer?
This tool only offers 5 and 10 seconds. To record longer and keep it as a file, use a voice recorder.