Skip to content
UtilPick.
My toolbox
All tools
Favorites
Saved tools

Loading…

Recently used

Tools you open will appear here.

Get the desktop app
Settings
UtilPick.
All tools
All tools/Online Spirit Level — Phone Bubble Level

Online Spirit Level — Phone Bubble Level

Turn your phone into a spirit level using its tilt sensor. Surface and edge modes, flip calibration and mm-per-meter readings. Sensor data stays on your device.

Loading the tool…

Used this tool? Share what worked for you — it helps the next person.

User reviews

No reviews yet.

Write a review

Checking your sign-in status…

    From first step to finished result

    Online Spirit Level — Phone Bubble Level: complete guide

    Walk through the steps and examples, or jump straight to the topic you need.

    How to use
    Examples & choices
    Troubleshooting
    FAQ

    At a glance

    How it measures
    It uses the phone browser's tilt sensor (deviceorientation) to work out the direction of gravity. No app installation is needed.
    Two modes
    Surface mode lays the screen face up to read left-right and front-back tilt. Edge mode stands the phone up and presses a side against the object to read the angle away from the 0, 90, 180 and 270° references.
    Units
    Besides the angle (°), it shows slope (%) = tanθ × 100 and height difference per meter (mm) = tanθ × 1000. Enter your object's length and it tells you the height to correct in mm.
    Calibration
    Supports Set zero and a flip (180°) calibration that works without a flat reference surface. Calibration values are stored only in this browser.
    Accuracy
    The sensor reads in 0.1° steps and varies from device to device, so treat it as a reference with roughly ±0.2 to 0.5° of error.
    Permission and storage
    On iPhone, tapping Start asks for sensor permission. Sensor values are never sent to a server.

    How to use Online Spirit Level — Phone Bubble Level

    1. 01

      Tap Start and allow permission

      When you tap Start, an iPhone asks for motion and orientation access. Choose Allow. On Android it usually starts right away.

    2. 02

      Pick a mode and place it on the object

      For floors, desks and the top of a washing machine, use Surface mode with the screen lying face up. For shelves, picture frames and TVs, use Edge mode and stand the phone up with a side against the object.

    3. 03

      Calibrate if needed

      If there is a camera bump or a case, use flip calibration. Tap First reading, then turn the phone 180° on the same spot and tap Second reading, and the tool separates the device's error from the real tilt.

    4. 04

      Read the result and adjust

      If it is level, a check icon and "Level" appear; if not, the higher side and the angle are shown in text. Enter your object's length to see how many mm to raise or lower it, and use Hold value to freeze a reading.

    What it’s good for

    Why flip calibration is needed

    The back of a phone is not flat because of the camera bump or a case, and the sensor has some error that varies from device to device. If you take two readings on the same spot, turning the phone 180° in between, you can separate the device's error from the real tilt without needing a flat reference surface.

    Seeing it in mm instead of degrees

    A small angle like 0.3° is hard to picture. Enter the length of your object and the tool tells you how many mm to raise or lower one side. If a 60 cm shelf is tilted 0.3°, that is about 3.1 mm.

    Worked examples

    When a 60 cm shelf is tilted 0.3°

    Input and settings
    Object length 60 cm
    Tilt 0.3° (right side higher)
    Result
    For a 60 cm length, lower the right side by 3.1 mm or raise the left side by 3.1 mm.
    Height difference = 600 mm × tan 0.3° ≈ 3.1 mm. 0.3° is hard to see by eye, but over 60 cm it makes a difference of more than 3 mm.

    A floor with a 2° slope

    Input and settings
    Surface mode
    Left-right tilt 2.0°
    Result
    Slope 3.49% · 34.9 mm per meter
    tan 2° × 1000 ≈ 34.9 mm, so two points 1 m apart differ in height by about 3.5 cm.

    Flip calibration

    Input and settings
    First reading +0.8°
    Second reading after a 180° turn −0.2°
    Result
    Device offset +0.3° · actual tilt of this floor +0.5°
    Device offset = (0.8 + (−0.2)) ÷ 2 = 0.3°, and actual tilt = (0.8 − (−0.2)) ÷ 2 = 0.5°. Later measurements are shown with the 0.3° device offset subtracted.

    Choosing a measuring mode

    Swipe the table sideways to see the rest.

    Choosing a measuring mode
    ModeUse it whenWhat to check
    Surface modeThe phone can lie on top, such as a floor, desk, washing machine or refrigeratorLine up the screen's left-right direction with the direction you want to measure, and calibrate if there is a case or camera bump
    Edge modeYou press a side against something, such as a shelf, picture frame, TV or window frameCheck that the phone's side is straight, and look at the reference angle (0 or 90°) too
    Hold valueYou measure in a spot where the screen is hard to seeThe time it was held is shown, and tapping release makes it live again

    When the result isn’t what you expected

    The permission prompt does not appear, or I denied it

    On iPhone, once you deny it, it does not ask again. Go to Settings → Safari → Advanced → Website Data, remove this site, open it again and tap Start.

    It says it cannot read the tilt sensor

    If no sensor reading arrives within 1.5 seconds, the device is treated as having no sensor. That is the case for most laptops and desktops. Open it on your phone using the QR code on the screen.

    The value keeps wobbling

    If it says there is movement, set the device down, take your hand off and wait a moment. If you are on a vibrating washing machine, stop it before measuring.

    The screen turns off

    With Keep screen on enabled, the tool asks that the screen stay on while measuring. In browsers that do not support it, a notice is shown.

    Key terms

    Slope (%)
    The height difference per 100 of horizontal distance. It is tanθ × 100, and 2° is about 3.49%.
    mm per meter
    The height difference between two points 1 m apart, in mm: tanθ × 1000.
    Flip calibration
    A method of taking two readings on the same spot with a 180° turn in between to separate the device's error from the real tilt. It is the same way carpenters check a spirit level.
    Tolerance
    The angle within which the surface is treated as level. You can choose from ±0.1, 0.3, 0.5 and 1°.

    Online Spirit Level — Phone Bubble Level FAQ

    Does it work on a computer?

    Most computers have no tilt sensor, so nothing can be measured. If there is no sensor, the tool shows a QR code you can open on your phone.

    Can I use it for construction work?

    Smartphone sensors read in steps of 0.1° and vary from device to device, so it is for reference only. For work that needs precision, such as building, use a dedicated spirit level.

    How is it different from the iPhone's built-in level?

    The iPhone's level is inside the Measure app. This tool opens in the browser with no installation and also shows slope (%), mm per meter, the height to correct, and flip calibration.

    Can I turn the phone sideways?

    If the screen rotates, the display rotates with it, so "Left is higher" always means the left of the screen you are looking at. Locking auto-rotate makes it easier.

    Jump to a topic

    • #surface or edge mode
    • #flip calibration
    • #sensor permission
    • #mm per meter

    Reviewed 2026.10.02

    Related tools

    View all
    Unit ConverterMoney & Math
    Pyeong ↔ m² Converter (Korea)Money & Math
    My Device SpecsDevice Tests
    UtilPick

    Simple tools for a complicated day. A free collection of online utilities.

    Service

    About UtilPick Get the desktop app

    Help

    Request a toolReport a problemContactinfo@utilpick.com

    Policies

    Privacy Policy (Korean)Terms of Use (Korean)
    Business registration no. 365-47-00936 (Republic of Korea)
    © 2026 UtilPick
    Featured on Twelve ToolsUtilPick - Featured on Startup FameFazier badgeFeatured on LaunchIgniter
    HomeSearchFavoritesMore

    Use your phone as a spirit level

    Tap Start and allow access to the motion sensor. Surface mode works with the phone lying screen-up; edge mode works with the phone standing on its long or short edge against an object.

    To use the tilt sensor, tap Start and choose Allow.

    Measuring mode
    Tolerance counted as level

    In surface mode, line up the screen’s left–right direction with the object’s length.

    Sensor readings are used only in this browser and never sent to a server.

    Phone sensors report in 0.1° steps and each device has errors of a few tenths of a degree, so treat this as a guide of roughly ±0.2–0.5°. Use a dedicated level for construction work. Calibrate first if your phone has a camera bump or case.

    If the screen rotates, the display rotates with it. Locking auto-rotate makes it easier.